Skip to content
NVX

Remote controller repair

Drone remote controller repair.

When the remote fails, a working drone cannot fly. NVX repairs DJI remote controllers, both screen remotes and the RC-N remotes that use your phone, and the radios used with FPV and other drones. Bring or courier the controller, and the drone too if the fault is linking.

Service charge

Drone service charge

Consumer and FPV drones

₹1,000

DJI Mini, Air, Mavic, Avata, Neo, Flip, Lito, FPV and other small drones.

Enterprise and agriculture drones

₹2,500

DJI Matrice, Mavic 3 Enterprise, DJI Agras and other agriculture drones, Saksham, BAAZ and other industrial drones.

Parts and repair work are quoted after the check, before any work starts.

Controller faults we repair

Tell us the controller model and what it does, or does not do.

Stick drift or a dead stick

The drone moves on its own or a stick does not respond.

Broken or blank screen

Cracked or black screens on remotes with a built-in display.

Will not charge or power on

Charging port, cable, battery or power-board faults.

Buttons and dials

Stuck or broken buttons, wheels and switches.

Weak signal or video drops

Antenna, cable or radio faults that shorten range.

Phone not detected

Cable, port or connector problems on RC-N remotes.

Controller will not link or charge

Try these first, then book a diagnosis if the problem stays.

Charge with a known-good charger

Charge for a while with the original or a known-good cable and charger before deciding it is dead.

Update both devices

A firmware mismatch between the drone and the controller can stop linking. Update both in the DJI app.

Re-link the controller

Use the app's link option with the drone switched on nearby.

Try another cable or phone

On RC-N remotes, a worn phone cable is a common cause of connection errors.

What decides the cost

It depends on the controller model and the part that failed: a phone cable or a stick module costs far less than a screen or a main board. Parts for some controllers take longer to find. NVX tests the controller, and the drone if needed, and quotes before any work.

How it works

The same tracked process for every repair, whether you visit or courier the drone.

1. Submit a repair request

Model, what happened and a few photos. It takes about three minutes.

2. Drop off or courier

Bring it to Connaught Place or send it by courier. Contact us first about damaged batteries.

3. Diagnosis and quote

A technician finds the fault and quotes before any work starts.

4. Repair, calibrate, test-fly

Approved work is done, sensors are calibrated, and the drone is test-flown where safe.

5. Collect or receive

Pick it up or get it couriered back, with a summary of the work done.

FAQ

Controller Repair: common questions

Do you repair DJI RC and RC 2 controllers?

Yes. We repair screens, sticks, charging and power faults and linking problems on DJI screen remotes, with a quote before any work.

Can you fix stick drift on a drone controller?

Usually, yes. Recalibrate the sticks in the app first. If the drift comes back, the stick module is worn or damaged and can be replaced.

My DJI controller will not connect to the drone. What should I do?

Update the drone and controller firmware, then re-link them in the app. If they still will not link, bring both to us so we can test which one has the fault.

Do you repair FPV radio transmitters?

We repair sticks, switches, charging and wiring faults on common FPV radios. Share the radio model in the repair request.

How much does drone controller repair cost?

It depends on the model and what failed. NVX diagnoses first and quotes before any work. The service charge is ₹1,000 for consumer and FPV drones and ₹2,500 for enterprise and agriculture drones.

Book a repair

Get a tracked service reference in minutes.

Visit us at C Block, C42/2, 1st Floor, Dwarka Sadan, Middle Circle, Connaught Place, New Delhi, Delhi 110001 (Mon-Sat, 11:00 AM-7:00 PM), or courier your drone from anywhere in India.

Related

Related services and products

More on this topic